Quick Installation Guide
TEW-640MB
1.01
1. Before You Start
Package Contents
ŸTEW-640MB
ŸCD-ROM (User's Guide)
ŸMulti-Language Quick Installation Guide
ŸPower Adapter (12V DC, 0.5A)
ŸNetwork Cable (0.6m/2ft.)
System Requirements
ŸA computer with network adapter installed
ŸWireless router (e.g. TEW-639GR) or access point (e.g TEW-690AP)
ŸAn available DHCP Server –wireless routers usually have a built-in DHCP server
ŸA media device (e.g. Game Console, Blu-ray player, Internet Ready TV, etc.) with
an Ethernet port
ŸWeb Browser: Internet Explorer (6.0 or higher)
1
2. Hardware Installation
Note:
1: Wi-Fi Protected Setup (WPS) allows you to quickly connect to your wireless router or
access point. If you would like to use WPS push button setup, please go directly to
section 4. Wi-Fi Protected Setup (WPS) Push Button Setup. If your wireless router
or access point does not support WPS, continue on to section 2 in the Hardware
Installation.
2: Do not connect/install the TEW-640MB to your network until instructed to do so.
1. Connect one end of the provided RJ-45
network cable to one of the TEW-640MB's LAN
ports. Connect the other end of the cable to
your computer's network port.
2. Connect the Power Adapter to the TEW-640MB
and then to a power outlet. EU Versions will
have a power button on the back. Push the
power button to the “On” position (EU Version).
Wait 30 seconds for the TEW-640MB to boot
up.
3. Verify that the following panel lights are on:
Wireless (Blue/Blinking)
Network Port (1-4) (Blue/Blinking)
Power (Blue/Solid)
2
3. Configure the TEW-640MB
1. Open your web browser, type
and then press Enter.
2. Enter the User Name and password and then
click OK. Default Settings:
User name: admin
Password: admin
Note: User name and Password are case
sensitive.
3. The Wizard will automatically appear. Click
Administration Ž Wizard if the Wizard does
not automatically appear.
4. Click Next.
5. Select Manual Setup and then click Next.
3
6. Select DHCP to have the TEW-640MB
automatically obtain an IP address from your
DHCP server (router). If Static IP address is
selected you would need to configure the
following:
IP address: The assigned IP address should be
similar to your network. This IP address should
not be used by any other network device on
your network.
Subnet Mask: In most cases, the default
Subnet Mask (255.255.255.0) should be fine.
Default Gateway: Enter the IP address of your
router for the Default Gateway.
Then click Next.
7. Click Scan.
8. Select a SSID and then click Select. The SSID
is the wireless network name of your wireless
network (e.g. wireless router or access point).
9. Click Next.
10. If Encryption is enabled on your wireless
network (e.g. access point or wireless router)
the correct Security Mode and Algorithm will
be automatically selected. Enter the Pass
Phrase (wireless network password) and then
click Apply.
4
11. Verify that your settings are correct and then
click Apply.
12. Click OK.
13. Wait while your settings are being applied.
14. Click Export Setting (optional). This saves
your configuration settings in a file, which can
be reloaded when needed.
15. Click Save (optional).
16. Give the file a name, then click Save.
5
17. Click Exit Wizard.
18. Unplug the power adapter and disconnect the
TEW-640MB from your computer. Place the
TEW-640MB in your desired location. Please
refer to the Wireless Tips section for optimal
placement of the TEW-640MB.
19. Plug the power adapter of the TEW-640MB
and connect one end of a network cable to
one of the TEW-640MB's LAN ports. Connect
the other end of the cable to your media
device's (e.g. Game Console, Blu-ray player,
Internet Ready TV, etc.) network port. Verify
that the following panel lights are on: Power
(Blue/Blinking), Network Port (1-4)
(Blue/Blinking), and Wireless (Blue/Blinking)
20. Verify that your network media device is
connected to your network. If the network
setting on your media device is set to obtain
an IP address automatically (dynamic IP) an
IP address will be assigned automatically.
Please refer to the manual or contact your
media device's technical support for
instructions.
Configuration is complete
For detailed information regarding the TEW-640MB’s configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
Thank you for choosing TRENDnet
6
|