VDO Dayton Automobile Accessories RV 5100 User Manual

RV 5100  
Mounting instruction  
Manuel d’installation  
Einbauanleitung  
Inbouwhandleiding  
Istruzioni d’installazione  
Instrucciones de montaje  
Monteringsanvisning  
 
3
 
General  
The RV 5100 is a black& white CCD backing up camera designed for use with VDO and  
VDO Dayton Multimedia Systems.  
Features:  
no extra supply voltage needed (12 V power supply by Multimedia System)  
automatic switch-on when you shift to the reverse gear (if signal is connected).  
high resolution CCD Image Sensor  
automatic aperture control for optimum adaption to lighting conditions  
aperture angle: 130° diagonal  
waterproof die-cast camera housing  
high operating temperature range  
Safety precautions  
ATTENTION:  
Installation may only be carried out by trained specialists! Observe all quality  
standards of the automobile industry!  
A
Fire hazard! When drilling pay attention to the location of cable harnesses, tank and  
fuel pipes! Never drill into car parts which are load-bearing or are important for safety  
reasons!  
A
Consult with your authorized car dealer if installation requires the drilling of holes or  
other modifications of the vehicle.  
A
Refer to the owner's manual for details on connecting the other units, then make  
connections correctly.  
A
Use only the parts included with the unit to ensure proper installation. The use of  
unauthorized parts can cause malfunctions.  
A
Route and secure all wiring so it cannot touch any moving parts, such as the gear shift,  
handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater  
outlet.  
A
5
 
Scope of delivery  
1
1
1
1
1
1
3
3
3
2
2
4
Mounting instructions  
Camera with cable (1.15 m) and rubber gasket  
Extension cable 18 m  
Mounting bracket (stainless steel)  
Sun visor (stainless steel)  
Strip self-adhesive rubber seal  
Self-tapping screws 4 x 10  
Spring washers M4  
Washers M4  
Screws M3 x 6  
Spring washers M3  
Screws M3 x 8 with spring and washer  
Mounting  
1. Mount the supplied mounting  
bracket to the vehicle with  
Self-tapping screw 4 x 10  
Spring washer M4  
self-tapping srews 4 x 10 and spring  
washers and washers M4 (for  
example on the plastic bumper).  
2. Use self-adhesive rubber seal to  
protect vehicle body from scratches,  
if necessary.  
Mounting bracket  
3. If no sufficient hole for the camera  
cable is available, drill a hole with a  
diameter of 19 mm into the vehicle  
body. Deburr all holes and apply  
suitable rust protection.  
Adhesive tape  
Protective paper  
4. Pass camera cable through into the  
vehicle using the rubber gasket.  
Do not bend cable around sharp edges.  
5. Mount the camera and the sun visor to the bracket using the 6 supplied screws.  
Do not yet tighten screws.  
Screws M3 x 8  
Sun visor  
Spring washer M3  
Screw M3 x 6  
6
 
6. Connect camera cable as described  
in section “Connecting the camera”  
on the next page. If required, use  
the supplied extension cable.  
Connecting the camera  
The camera can be connected to your Multimedia System in different ways:  
1. Direct connection to the Navigation Computer, ill. 1  
For direct connection of the camera to the navigation computer the adaptor cable  
MA 1200 (accessory) is required.  
Connect the Mini DIN plug of the camera to the Mini DIN socket of the MA 1200.  
Activate the “Rear view camera connected” option in the “System Settings –> Video  
configuration” menu of the navigation computer.  
2. In combination with TV Tuner TV 5100, ill. 2  
Connect the Mini DIN plug of the camera to the camera input of the TV 5100.  
Connect the yellow lead of the TV 5100 to the reversing signal of the vehicle to  
ensure automatic switch over to the camera when backing up.  
3. In combination with Multimedia Interface Box MI 5000, ill. 3  
Connect the Mini DIN plug of the camera to the camera input of the MI 5000.  
Activate the “Multimedia box connected” option in the “System Settings –> Video  
configuration” menu of the navigation computer.  
4. In combination with TV Tuner TV 5100 and MI Box MI 5000, ill. 3  
Connect the Mini DIN plug of the camera to the camera input of the MI 5000.  
Activate the “Multimedia box connected” option in the “System Settings –> Video  
configuration” menu of the navigation computer.  
Checking function and adjusting the camera  
1. Switch on ignition.  
2. Apply handbrake and select reverse gear.  
The picture of the backing up camera has to be shown on the display.  
3. Adjust the camera to the desired viewing angle and tighten all screws.  
4. Select any forward gear.  
The picture of the backing up camera now has to disappear from the display.  
7
 
Specifications  
Picture system: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/3 inch CCD sensor  
Resolution: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270,000 pixel (CCIR)  
Horizontal resolution: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 TV lines  
Synchronisation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Hz internal  
Lens: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 mm / F = 2.0  
Sensitiveness: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,1 Lux min.  
Supply voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . + 12 V / DC  
Power consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 W  
Operating temperature range: . . . . . . . . . . . . . . . . . . . . . . . . . - 10° Celsius to + 60° Celsius  
Dimensions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 mm x 57 mm x 44 mm (W x D x H)  
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 g  
Connection details  
PIN No.  
Description  
1
2
3
4
5
+ 12 V DC power supply  
Video output signal  
NC  
NC  
Ground  
Troubleshooting  
If you discover any malfunction of the camera after installation, please check all  
connections and installation steps according to the mounting instructions.  
If you can't solve the problem, please contact our Customer Help Desk:  
G
Q
0121 344 5400  
(03) 94503166  
Subject to technical modifications and errors.  
8
 
RV 5100  
07/2001 ri  
 

Tascam Recording Equipment VL X5 User Manual
TOA Electronics Digital Camera C CV14 CS User Manual
TOA Electronics Ventilation Hood SSDVT 4035CNM User Manual
Toastmaster Bread Maker 1170S User Manual
Toshiba CRT Television 34HF81 User Manual
Toshiba Flat Panel Television 27A46C User Manual
Triarch Indoor Furnishings 25691 User Manual
Tripp Lite Network Card PDU1415 User Manual
Vanguard Managed Solutions Electric Heater Birch Log Design User Manual
Vinotemp Beverage Dispenser VT BD User Manual